3-axle low-loader trailer with straight platform
- High point loading due to narrow cross member spacing
- Waterproofed softwood floor, protruding beyond frame profiles
- 5 pairs of recessed foldable lashing rings
- Installation of axles from well-known manufacturers such as SAF or BPW
- OPTIONAL: Foldable, pivoting extensions, incl. extension planks for transporting wide loads
- OPTIONAL: Offset drawbar with pivoting eye 40 + 50 mm
- OPTIONAL: Version with side walls
- OPTIONAL: 2-part loading ramps with motor-hydraulic ramp actuators
- OPTIONAL: Ramps with hydraulic lateral movement, operated on semitrailer
- OPTIONAL: Plug-in retaining rails
- OPTIONAL: SmartBoard for reading data on vehicle display (mileage, axle assembly load, brake diagnostics etc.)
3-AXLE LOW LOADER TRAILER - TYPE TÜP
Gross weight (techn.): 30 t
Payload: approx. 24 t
Gross weight (perm.): 24 t
Tare weight: approx. 5,9 t
Approx. 7,000 mm = flat load surface
Approx. 1,000 mm = rear access slope
Total width: 2,550 mm
Loading height, laden: approx. 960 mm
Welded steel construction without front frame offset or body offset
and drive-on taper at rear
4 pairs of mounting pockets for 100 x 5 0 mm tubular posts in external frame
Recess in access slope for excavator shovel linkage
6 pairs of lashing points under external frame
5 pairs of recessed foldable 5 t lashing rings in floor (10 t techn. tensile strength)
Reinforced, maintenance-free parabolic springs
Low-loader axles, each with 11 t axle load
S-cam brake 300/200 mm, autom. brake linkage adjuster
Dual-axle compensation
Tyres :
12 x 2 4 5/7 0 R 17.5 14 3 J, manufacturer as per factory specifications
12 steel wheel rims 6.75 x 17.5, 10-hole, with rim offset, silver
Brake system according to EC Directive 71/320 or E CE R13
Two-line brake
EBS - electronic brake system
Wabco 4S3M = 1st and 2nd axles sensed
Spring-loaded parking brake on 2nd and 3rd axles
Steel air tank
Softwood floor 50 mm, waterproofed, protruding approx. 5 - 10 mm beyond frame profiles
2 foldable, 1-part loading ramps, approx. 2,700/710 mm, with hardwood flooring
Ramp width manually adjustable by approx. 550 mm, with rod,
(min. spacing approx. 295 mm up to max. total width of 2,815 mm)
lockable in driving position using chains with turnbuckle
2 autom. folding supports at rear
Lifting aid with coil spring
24 V lighting system according to EC Directive 76/756/ EWG
2 five-chamber tail lights on ramps
LED side marker lights
2 clearance lamps
2 contour lights
Fixed cable(s) with 2 x 7-pin or 1 x 15-pin connector
Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)
Plastic and hot-dip galvanised parts (extensions etc.) unpainted,
powder-coated attachments/installation parts and drawbar black
Reflective contour marking strips across entire length of sides and on the rear (white on sides and red at rear by default), according to ECE 48
Rear markings as per ECE standards
Wheel chock(s) as per regulations
Plastic mudguards or splashguards with spray protection as per regulations
Side impact protection
Spare wheel well for 1 spare wheel
Centre of gravity marking
Fixed drawbar, 40 mm drawbar eye, 5° angle ,
with silent bushing
Your Schwarzmüller contact persons
Always nearby. We are delighted to help.