3-axle 3-way tipper semitrailer - long-haul transport

  • Stable and torsionally rigid chassis construction with additional torsion tubes for 3-way tipping
  • Automatic rear wall locking
  • Installation of axles from well-known manufacturers such as SAF or BPW
  • OPTIONAL: 2 mechanical steel support winches with rollers at frame end
  • OPTIONAL: Plastic roller tarpaulin incl. aluminium pole and hand crank
  • OPTIONAL: Electropneumatic side wall locking with switch operation in cab
  • OPTIONAL: Foldable lashing rings
  • OPTIONAL: Aluminium flap on lateral central locking shaft
  • OPTIONAL: Standing platform comprising aluminium safety grid with guardrail and step unit at front wall
  • OPTIONAL: sliding tarpaulin frame
  • OPTIONAL: Grain-tight side wall mounting with labyrinth sealing system
TYPE DESIGNATION

3-AXLE 3-WAY TIPPER SEMITRAILER - LONG-HAUL TRANSPORT

For pallet and grain transport etc.

 

DIMENSIONS

Internal length: approx. 13,400 mm

Internal width: approx. 2,460 mm

Internal height: approx. 2,200 - 2,400 mm

Total width: 2,550 mm

Total height, unladen: approx. 3,800 - 4,000 mm

Loading height: approx. 325 mm over fifth-wheel height

 

FRAME

Naxtra welded steel frame construction - low design height

Connector lock for tipper body with cross-over protection

Replaceable 2" kingpin

 

CHASSIS

Air suspension with autom. lowering device via inductive switch and lowering lock via rotary switch on semitrailer


air suspension unit with low-maintenance 430 mm disc brake axles, 3 x 9 t rigid, wheelbase 2 x 1,310 mm


Tyres :

6 x 385/65 R 22.5 160J, manufacturer as per factory specifications

6 steel wheel rims 11.75 x 22.5, 10-hole, with rim offset, silver

 

SUPPORT FIXTURES

Mechan. 24 t support jacks with single-sided operation, low-maintenance

 

BRAKE SYSTEM

Brake system according to EC Directive 71/320 or E CE R13

Two-line brake

Spring-loaded parking brake on 2 axles

EBS - electronic brake system

Wabco 2S2M = one axle sensed

RSS - stability program

Steel air tank

 

TIPPING SYSTEM

2 special tipper cylinders for 3-way tipping, installed in series

1 arrester cable

Rearward tipping angle: approx. 34°

1 pipe system with screw coupling DN20

 

ELECTRICAL EQUIPMENT

24 V lighting system according to EC Directive 76/756/ EWG

2 seven-chamber tail lights in underride protection

LED side marker lights

2 clearance lamps

2 contour lights

2 x 7-pin / 1 x 15-pin socket

 

PAINTWORK

Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)


Plastic and hot-dip galvanised parts unpainted,

powder-coated attachments/installation parts black


Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48

 

ATTACHMENTS

Wheel chock(s) as per regulations

Noise dampers

Single wheel plastic mudguards with spray protection as per regulations

Side impact protection

Aluminium underride protection, coated white

1 spare wheel bracket for 1 spare wheel

1 integrated level gauge (to check horizontal position during rearward tipping)

 

WEIGHTS

Gross train weight (perm.): 40 t

Gross weight (techn.): 39 t

Axle assembly load (techn.): 27 t

Fifth-wheel load (techn.): 12 t

Payload: approx. 25 t

Tare weight: approx. 8, 9 t

 

TIPPING LOADING RAMP

Full-steel welded construction with fine-grained special steel floor panels, 5 mm

(slight floor unevenness possible due to weld distortion)

 

SIDE WALLS

Grain-tight side wall mounting with labyrinth sealing system

Fixed steel plate front wall, 3 mm, approx. 1,700 mm high

3-part reinforced aluminium hollow profile side walls, 40 mm, approx. 780 mm high, (top and bottom profiles reinforced 4/2 mm, 2 x 200 mm intermediate profiles 2/2 mm), with vertical special sealing groove and bracket recess for tarpaulin overhang (360 mm), without tarpaulin brackets, foldable with extended swivel bolt locks and hinged with man. central locking (operated separately for each wall)

Aluminium hollow profile rear wall, 40 mm, approx. 780 mm high, foldable with extended swivel bolt locks and hinged with man. central locking

 

POSTS/COVER

2 fixed front corner posts, integrated in front wall, 2,000 mm high

4 foldable centre posts, 2,000 mm high (split approx. at side wall height,

lower section foldable, upper section removable with roof rack support)

Tension chain with fastener for centre posts

2 fixed rear corner posts, 2,000 mm high, welded to sides

4 rows of softwood slot-in slats, 100/27 mm, in pockets, 200 mm spacing

1 slat at front


Tarpaulin bows with 7 rows of roof poles and transverse bows for pillars, without inclination

(crane and stacker loading)

 

ACCESSORIES

Rear markings as per ECE standards

 

 

H_KippSanh3S3AFern_PIC1.jpg
3-axle 3-way tipper semitrailer - long-haul transport
H_KippSanh3S3AFern_PIC7.jpg
OPTIONAL: 2 mechanical support winches with rollers at frame end
H_KippSanh3S3AFern_PIC10.jpg
OPTIONAL: Aluminium flap on lateral central locking shaft
H_KippSanh3S3AFern_PIC8.jpg
OPTIONAL: Foldable lashing rings
H_KippSanh3S3AFern_PIC4.jpg
Stable and torsionally rigid chassis design with additional torsion tubes for 3-way tipping
H_KippSanh3S3AFern_PIC9.jpg
Manual central locking to open the side walls using a lever and central locking shaft
H_KippSanh3S3AFern_PIC5.jpg
Fixed steel sheet front wall, 3 mm
H_KippSanh3S3AFern_PIC6.jpg
Aluminium hollow profile rear wall, folding with extended swivel bolt locks and hinged with man. central locking

Your Schwarzmüller contact persons

Always nearby. We are delighted to help.

Premium even at customer service

From maintenance to vehicle rental