3-axle 3-way tipper trailer - building site

  • Tipper body construction using conical, trapezoidal profile side members in high-strength, lightweight design with small bottom panels for high dent resistance and shock absorption
  • Insulated hollow chamber body for slow cooling, freezing and adhesion of load
  • Hard chrome-plated, high-quality tilt cylinder
  • Installation of axles from well-known manufacturers such as SAF or BPW
  • OPTIONAL: Pull-out drawbar, max. 600 mm adjustment, with Getofix drawbar support
  • OPTIONAL: Bordmatic (= hydraulically folding side wall) on left side
  • OPTIONAL: Reinforced side walls with material-repellent membrane construction made from fine-grained special steel panels
  • OPTIONAL: Electropneum. side wall pendulum locking with switch operation in cab
  • OPTIONAL: Aluminium flap on lateral central locking shaft
  • OPTIONAL: Standing platform comprising aluminium safety grid with guardrail and step unit
  • OPTIONAL: Foldable lashing rings

For handling bulk materials such as sand, gravel, rubble, ground excavation etc. on building sites


Internal length: approx. 7,300 mm
Internal width: approx. 2,420 mm
Total width: 2,550 mm
Loading height, unladen: approx. 1,390 mm


Naxtra welded steel frame construction
Connector lock for tipper body with cross-over protection


Air suspension with autom. lowering device via inductive switch

Drum brake axles, S-cam brake 420/180 mm, autom. brake linkage adjuster
each with 9 t axle load

Tyres :
6 x 385/65 R 22.5 160J, manufacturer as per factory specifications
6 steel wheel rims 11.75 x 22.5, 10-hole, 120 mm rim offset, silver


Brake system according to EC Directive 71/320 or ECE R13
Two-line brake
Spring-loaded parking brake on 2nd and 3rd axles
EBS - electronic brake system
Wabco 4S3M = 1st and 3rd axles sensed
RSS - stability program
Steel air tank


1 tipper cylinder for 3-way tipping, approx. 40 t initial lifting force,
1 arrester cable
1-pipe system with hydraulic connecting hose incl.
plug-in coupling NW13, without truck attachments


24 V lighting system according to EC Directive 76/756/EWG
2 seven-chamber tail lights
LED side marker lights
2 clearance lamps
2 contour lights
Fixed cable(s) with 2 x 7-pin or 1 x 15-pin connector


Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)

Plastic and hot-dip galvanised parts unpainted,
powder-coated attachments/installation parts black

Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48


Wheel chock(s) as per regulations
Noise dampers
Fixed aluminium trapezoidal underride protection, unpainted
Single wheel plastic mudguards with spray protection as per regulations
1 spare wheel bracket for 1 spare wheel
Side impact protection made from aluminium profiles as per regulations, coated black
Hooks for dosing chains on swivelling rear wall


Gross weight (techn.): 27 t
Gross weight (perm.): 24 t
Payload: approx. 18 t
Tare weight: approx. 5. 7 t


Full-steel welded construction with fine-grained special steel floor panels, 5 mm
(slight floor unevenness possible due to weld distortion)


Fixed steel plate front wall, 3 mm, approx. 900 mm high
2-part reinforced aluminium hollow profile side walls, 60/40 mm, approx. 780 mm high, foldable with extended swivel bolt locks and spring lifting aid, hinged with man. central locking (operated separately for each wall)
Aluminium hollow profile rear wall, 60/40 mm, approx. 780 mm high, foldable with extended locks and hinged with man. central locking


Rear markings as per ECE standards


2 fixed centre posts in side wall height
2 fixed rear corner posts in side wall height, welded to sides


Fixed drawbar , 40 mm drawbar eye , with silent bushing and drawbar locking device

Your Schwarzmüller contact persons

Always nearby. We are delighted to help.

Premium even at customer service

From maintenance to vehicle rental