3-way tipper body for 2A truck - building site

  • Insulated hollow chamber body for slow cooling, freezing and adhesion of load
  • Tipper body construction using conical, trapezoidal profile side members in high-strength, lightweight design with small bottom panels for high dent resistance and shock absorption
  • Torsionally rigid, weight-optimised subframe construction
  • Hard chrome-plated, high-quality tilt cylinder
  • OPTIONAL: Bordmatic (= hydraulically folding side wall) on left side
  • OPTIONAL: Reinforced side walls with material-repellent membrane construction made from fine-grained special steel panels
  • OPTIONAL: Electropneumatic side wall locking with switch operation in cab
  • OPTIONAL: Aluminium flap on lateral central locking shaft
  • OPTIONAL: Foldable lashing rings
  • OPTIONAL: Foldable aluminium underride protection for road-finishing use
  • OPTIONAL: Front and rear crane mounting with reinforced subframe
TYPE DESIGNATION

3-WAY TIPPER BODY ON 2-AXLE TRUCK - BUILDING SITE
For handling bulk materials such as sand, gravel, rubble, ground excavation etc. on building sites

WEIGHTS

Body weight: approx. 1.7 t

DIMENSIONS

Internal length: approx. 4,500 mm
Internal width: approx. 2,420 mm
Load volume: approx. 7.5 m³
Total width: 2,550 mm

Body height, loading height etc. can only be checked and announced upon specification of the
exact truck data

PAINTWORK

Blasted with steel granulate, treated with zinc dust primer and spray painted
2-component acrylic paints for commercial vehicles (standard RAL or truck colour)

Plastic and hot-dip galvanised parts unpainted,
powder-coated attachments black

Reflective contour marking strips across entire length of sides (continuing onto truck cab) and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48

ACCESSORIES

Rear markings as per ECE standards
 

ATTACHMENTS

Tipper body rubber centre support
Bracket for wheel chock(s)
Mud flaps for rear mudguards
Shovel and brush brackets
Rubber skirting on side walls on both sides
Rubber bump stops on end plate
Hooks for dosing chains on swivelling rear wall

SIDE WALLS

Fixed steel plate front wall, 3 mm, approx. 980 mm high

1-part reinforced aluminium hollow profile side walls, 60/4/3 mm, approx. 680 mm high,
foldable with extended swivel bolt locks and spring lifting aid,
hinged with man. central locking
Aluminium hollow profile rear wall, 60/4/3 mm, approx. 780 mm high,
hinged with raised bearing and pneum. locking opened from cab,
foldable with extended swivel bolt locks

Fixed rear corner posts, raised, side-mounted

SUBFRAME

Continuous side members with tilt cylinder bearings and outriggers
Body height above chassis: approx. 400 mm
Connector lock for tipper body with cross-over protection

HIGH-PRESSURE HYDRAULIC TIPPING SYSTEM

16 t tilt cylinder for 3-way tipping, with safety rope,
40 l pump for direct flange mounting, 35 l oil reservoir with oil filling,
pneum. tip valve with overpressure protection and actuation in cab

TIPPING LOADING RAMP

Full-steel welded construction with fine-grained special steel floor panels, 5 mm
HARDOX HB450
(slight floor unevenness possible due to weld distortion)

L_KippAuf3S2ABauSte_PIC3.jpg
3-way tipper body on 2-axle truck - building site
L_KippAuf3S2ABauSte_PIC7.jpg
OPTIONAL: Foldable lashing rings
L_KippAuf3S2ABauSte_PIC5.jpg
Hard chrome-plated, high-quality tilt cylinder
L_KippAuf3S2ABauSte_PIC4.jpg
Tipper body design with conical trapezoidal profile side members in high-strength, lightweight design with small bottom panels for high dent resistance and shock absorption
L_KippAuf3S2ABauSte_PIC6.jpg
OPTIONAL: Bordmatic (= hydraulically folding side wall) on left side

Your Schwarzmüller contact persons

Always nearby. We are delighted to help.

Premium even at customer service

From maintenance to vehicle rental