3-axle lightweight platform semitrailer - coil - inclined loader

  • Hydraulic diagonal loading for transporting large format plates with up to 3,300 mm width
  • Electrohydraulic pump unit for manual operation of diagonal loading on semitrailer
  • Sliding cover, hydraulically foldable against inside of front wall for open plate transports
  • Coil recess with useful length of 8,000 mm (split into 3 segments ) for coil diameters from 900 to max. 2,100 mm
  • Hydraulic control unit for diagonal loading system
  • Stacker-bearing recess cover made from 40 mm resin-coated plywood with tubular trusses
  • Reinforced frame construction for coil transports of 27 t at centre of gravity across minimum 2,000 mm load length
  • Special system for transporting round plates
  • Sliding cover can be raised approx. 30° at the front for loading/unloading large format plates
  • Suitable for TIR customs sealing
  • Installation of axles from well-known manufacturers such as SAF or BPW
TYPE DESIGNATION

3-AXLE LIGHTWEIGHT PLATFORM SEMITRAILER - COIL - INCLINED LOADER

 

DIMENSIONS

Internal platform length: approx. 13,620 mm

Internal platform width: approx. 2,480 mm

Load space internal height: approx. 2,700 mm

Lateral loading height: approx. 2,640 mm

Rear loading height: approx. 2,700 mm

Loading height: approx. 140 mm over fifth-wheel height

 

FRAME

Welded steel frame construction - lightweight design

Reinforced for point loading = coil transport (27 t at centre of gravity across min. 2,000 mm length)

Frame for unladen fifth-wheel height of 1,120 - 1,220 mm


Replaceable 2" kingpin (EC installation dimension, width across corners: 2,040 mm)

23 pairs of recessed 2.5 t lashing points according to UVV, plus

6 pairs of 4 t lashing points in recess area on external frame

 

CHASSIS

Air suspension with lifting and lowering device (approx. +120/-80 mm)

Automatic adjustment of driving level from 15 km/h

Air suspension unit with low-maintenance disc brake axles, ø 430 mm, 3 x 9 t rigid, wheelbase 2 x 1,310 mm

Autom. lifting front axle = raised or lowered according to weight (with the lifting axle raised, the loading height or total height increases by approx. 50 mm)

When the 1st axle is raised, the vehicle does not follow the legal turning circle


Tyres :

6 x 385/55 R 22.5 160J, manufacturer as per factory specifications

6 steel wheel rims 11.75 x 22.5, 10-hole, 120 mm rim offset, silver

 

SUPPORT FIXTURES

Mechan. 2 x 12 t support jacks, single-sided operation and thrust compensation

 

BRAKE SYSTEM

Brake system according to EC Directive 71/320 or ECE R13

EBS - electronic brake system

Wabco 2S2M = one axle sensed

RSS - stability program

Spring-loaded parking brake on 2 axles

Aluminium air tank

 

FLOOR

Resin-coated plywood floor, 27 + 12 mm or 30 + 12 mm, flush with external frame

(floor load capacity: 5,460 kg stacker axle load acc. to CSC)

 

SIDE WALLS

Fixed aluminium hollow profile front wall, 2,000 mm, with 2 centre supports,

2 lashing rings inside for load securing

Inside of front wall reinforced with aluminium chequer plate, 3/5 mm, up to a height of 600 mm


4-part aluminium hollow profile side walls, 600/25 mm, with vertical and horizontal rubber seal, incl. 2 bracket recesses, spacing of bracket rows approx. 280 mm, lower row with standard tarpaulin brackets, max. 200 mm spacing, customs-compliant, upper row with standard tarpaulin brackets, max. 200 mm spacing, not customs-compliant in this case, foldable with Kinnegrip single locking


Foldable aluminium hollow profile rear wall, 600 mm high, with vertical and horizontal rubber seal, incl. 2 bracket recesses, tarpaulin brackets and spacing as for side walls,

foldable with Kinnegrip single locking

1 folding step

 

POSTS/COVER/TARPAULIN

Integrated extended lever locks, Kinnegrip system K20 with single locking

2 front corner posts, bolted, protruding from sides, in roof height

6 foldable Kinnegrip centre posts, split

2 rear Kinnegrip corner posts, foldable, side-mounted


5 rows of softwood slot-in slats, 100/27 mm, in pockets, spacing:

1 x 400 mm, then 200 mm


Edscha sliding tarpaulin frame, forward-sliding = pushed together

in loading area, without inclination, design height 95 mm, guide rail at front with extra division with spline end

Collapsed Edscha cover, hydraulically foldable against inside of front wall, folding down only possible in lowest cover position,

operation via pump unit on trailer (hydraulic cylinder and support protrude into loading area at the top when loading from the side)

Roof rack supports suitable for adjustable cover with unladen total height of 4,300 mm with bore holes and linchpins


Tarpaulin made from high-strength Trevira fabric with translucent roof, without side separation, incl. tarpaulin rope and assembly,

tarpaulin manufacturer as per factory specifications

 

ELECTRICAL EQUIPMENT

24 V lighting system according to EC Directive 76/756/EWG

2 seven-chamber tail lights in underride protection

LED side marker lights

2 clearance lamps

2 contour lights on underride protection

2 x 7-pin and 1 x 15-pin socket

1 rear 2-pin socket in underride protection

 

PAINTWORK

Blasted with steel granulate, treated with zinc dust primer and spray painted with 2-component acrylic paints for commercial vehicles

 

 

ACCESSORIES

Rear markings as per ECE standards

 

ATTACHMENTS

Rear crash guard with corner post protection

Wheel chock(s) as per regulations

Single wheel plastic mudguards with spray protection as per regulations

Aluminium underride protection, coated white

Side impact protection made from aluminium profiles as per regulations

1 spare wheel bracket for 1 spare wheel (rear right)

1 plastic toolbox, lockable, unpainted, on left after axle

 

CONTOUR MARKINGS

Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48

 

INCLINED LOADING SYSTEM

Special configuration with hydraulic inclined loading for transporting

large format plates. Loading and unloading of plates even in horizontal position, i.e. raising with full load weight = 4 recessed transverse

tubular supports in floor, extendible, with hydraulic 4-stage lifting cylinder (individual actuation of each hydraulic cylinder), sealed from below with brush seal (splash water protection), with additional tubular safety supports and connecting rods

In each case 5 round pipe bushings at bottom + slot-in retainers made from 50 mm round steel, approx. 300 mm high


Plus one slot-in, height-adjustable tubular post at both front and rear

with diagonal support in neck area and at rear


Electrohydraulic operation with pump unit incl. separate steel plate oil tank,

2-battery power supply incl. storage box on trailer and charging cable up to front of trailer

Battery switch on equipment bracket at front, mounted on right in direction in travel


2 recesses in external frame on left in direction of travel for transporting round plates

4 round pipe bushings for slot-in retaining posts on left in direction of travel on external frame

4 resin-coated plywood panels, 400 x 400 x 40 mm, as base for inclined plate loading

Perforated steel rail recessed in floor up to first tubular support at front left in direction of travel, incl. 1 load securing wedge for front stop

 

COIL RECESS

Useful length: approx. 8,000 mm - special version for coil ø of 900 to max. 2,100 mm, 2 divisions in area of diagonal load beams,

with stacker-bearing cover made from 40 mm resin-coated plywood with tubular supports

5 pairs of racks = 1 x front, 1 x approx. 1,840 mm (before centre of gravity), 1 x 2,520 mm, 1 x 3,680 mm, 1 x 5,330 mm

incl. 2 pairs of tubular safety supports, 90 x 90 x 4 mm, useful height: approx. 1,700 mm

Inclinations on both sides made from 24 mm resin-coated plywood

 

W_PSanh3ALCBW_Schraegverlader_PIC3.jpg
3-axle lightweight platform semitrailer - coil - inclined loader
W_PSanh3ALCBW_Schraegverlader_PIC4.jpg
Hydraulic inclined loading device to transport large-format sheet metal up to 3,300 mm wide
W_PSanh3ALCBW_Schraegverlader_PIC5.jpg
Load area with retracted inclined loading device
W_PSanh3ALCBW_Schraegverlader_PIC6.jpg
Recessed tubular supports, extendible with hydraulic 4-step lifting cylinder
W_PSanh3ALCBW_Schraegverlader_PIC7.jpg
Electrohydraulic pump unit for independent operation of the inclined loading device on the semitrailer
W_PSanh3ALCBW_Schraegverlader_PIC8.jpg
Hydraulic control unit for inclined loading system
W_PSanh3ALCBW_Schraegverlader_PIC9.jpg
Coil recess with useful length of approx. 8,000 mm (split into 3 segments) - for coil diameters of between 900 and a max. of 2,100 mm
W_PSanh3ALCBW_Schraegverlader_PIC10.jpg
Sliding cover, hydraulically foldable against inside of front wall for open plate transports

Your Schwarzmüller contact persons

Always nearby. We are delighted to help.

Premium even at customer service

From maintenance to vehicle rental