3-axle low loader semitrailer with offset platform - reinforced - extendible

  • Drop deck with pull-out central frame, incremental adjustment with pneumatic locking
  • Offset platform raised at the front, incl. plug-in side walls
  • - Drop-deck loading platform with softwood floor and tubular posts in external frame
  • Pull-out extensions, incl. extension planks for transporting wide loads
  • Loading ramps with hardwood flooring and welded square ribs
  • 4 recessed foldable lashing rings on drop deck, and 5 pairs of lashing points on external frame
  • Third axle is steered trailing axle for improved cornering and lower tyre wear
  • Pull-out/removable warning signs front and rear, incl. position and marker lights for wide loads
  • Installation of axles from well-known manufacturers such as BPW or SAF
  • OPTIONAL: Ramps with hydraulic lateral movement, operated on semitrailer
  • OPTIONAL: Wheel recesses for transporting special vehicles
  • OPTIONAL: 2-part loading ramps with motor-hydraulic ramp actuators
TYPE DESIGNATION

3-AXLE LOW LOADER SEMITRAILER - REINFORCED - EXTENDIBLE

BRIDGE PLATFORM

Approx 3,500/2,550 mm or approx. 2,480 mm between walls = front offset platform
Approx. 7,800/2,550 mm = drop-deck platform - flat load surface
Approx. 1,000/2,550 mm = rear access slope
Total width: approx. 2,550 mm or approx. 3,000 mm with extension
Loading height, laden: approx. 940 mm
Horizontal position of semitrailer at laden fifth-wheel height of approx. 1,220 mm

FRAME

Extendible welded steel construction with tapered frame offset at front
and drive-on taper at rear

Drop deck with central frame extendible by approx. 5,000 mm, pneum. lockable at intervals of approx. 500 mm with operation on trailer

Replaceable 2" kingpin
2 folding supports at end of frame
5 pairs of mounting pockets on drop deck incl. tubular posts 100 x 50 x 5 mm,
useful height approx. 1,000 mm, hot-dip galvanised
5 pairs of lashing points on external frame
4 recessed foldable 5 t lashing rings (10 t techn. tensile strength) on drop deck
Storage for extension planks below loading platform when not in use.

CHASSIS

Air suspension with lifting and lowering device, for loading and unloading
Automatic adjustment of driving level from 15 km/h

Air-sprung low-loader unit with low-maintenance axles,
3 x 10 t, wheelbase 2 x 1,310 mm,
S-cam brake 300/200 mm, autom. brake linkage adjuster
1st and 2nd axles rigid,
steering knuckle 3rd axle = friction-steered trailing axle (20° steering angle) incl. electropneum. reverse gear interlock with switch operation in cab and additional operation on semitrailer

Tyres :
12 x 235/75 R 17.5 141J, manufacturer as per factory specifications
12 steel wheel rims 6.75 x 17.5, 10-hole, with rim offset, silver ex-works

SUPPORT FIXTURES

Mechan. 2 x 12 t support jacks, single-sided operation and thrust compensation

BRAKE SYSTEM

Brake system according to EC Directive 71/320 or ECE R13
Two-line brake
EBS - electronic brake system
Wabco 2S2M = one axle sensed
RSS - stability program
Spring-loaded parking brake
Steel air tank

FLOOR

Softwood floor 50 mm, waterproofed, protruding beyond frame profiles by approx. 5 mm at offset platform and 15 mm on drop deck, or beyond steel stud plate cover over rear wheels

WALLS/POSTS

Plug-in side walls on offset platform, 400 mm high, steel front wall,
25 mm aluminium hollow profile walls at sides and rear, with latch-type tension locks, plug-in rear corner posts in side wall height

EXTENSION

Foldable = pivoting extensions, on both sides of drop deck and rear
taper incl. continuous wooden boarding = also floor boards
between side members when used without extensions

RAMPS

2 foldable, 1-part loading ramps, approx. 2,700/700 mm, with hardwood flooring
Ramp width manually adjustable by approx. 580 mm, with rod,
(min. spacing approx. 265 mm up to max. total width of 2,850 mm)
lockable in driving position using chains with turnbuckle
2 autom. folding supports at rear
Lifting aid with coil spring

ELECTRICAL EQUIPMENT

24 V lighting system according to EC Directive 76/756/EWG
2 five-chamber tail lights on ramps
LED side marker lights
2 clearance lamps
2 contour lights
2 x 7-pin sockets at front
2-pin socket at rear for revolving beacon

PAINTWORK

Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)
Side and rear walls anodised (natural aluminium)
(for manufacturing reasons, colour deviations are possible in the case of anodised components)
Plastic and hot-dip galvanised parts unpainted,
powder-coated attachments/installation parts black

CONTOUR MARKINGS

Reflective contour marking strips across entire length of sides and on the rear (white on sides and red at rear by default), according to ECE 48

ACCESSORIES

Rear markings as per ECE standards
 

ATTACHMENTS

Wheel chock(s) as per regulations
Plastic mudguards or splashguards with spray protection as per regulations
Spare wheel well for 1 spare wheel
Side impact protection
Pull-out/removable warning signs front and rear, incl. position and
marker lights for wide loads up to 3,000 mm
Externally welded square ribs on ramps and rear access slope
Centre of gravity marking

Your Schwarzmüller contact persons

Always nearby. We are delighted to help.

Premium even at customer service

From maintenance to vehicle rental