2-axle 3-way tipper semitrailer - building site - reinforced

2-AXLE 3-WAY TIPPER SEMITRAILER - BUILDING SITE - REINFORCED
For handling bulk materials such as sand, gravel, rubble, ground excavation etc. on building sites

Internal length: approx. 7,150 mm
Internal width: approx. 2,420 mm
Total width: 2,550 mm
Loading height, unladen: approx. 330 mm over fifth-wheel coupling

Naxtra welded steel frame construction
Connector lock for tipper body with cross-over protection
Replaceable 2" kingpin

Air suspension with autom. lowering device via inductive switch and lowering lock via rotary switch on semitrailer

Air suspension unit with low-maintenance 430 mm disc brake axles, off-road version,
2 x 10 t rigid, wheelbase 1,310 mm

Autom. lifting front axle = raised or lowered according to weight, as well as forced lowering incl. integr. speed-restricted moving-off aid with button operation in cab (no button installation on our part)

Tyres :
4 x 445/65 R 22.5 168K, manufacturer as per factory specifications
4 steel wheel rims 14.00 x 22.5, 10-hole, without rim offset, silver

2 steel support legs, height-adjustable (only detachable when unladen)

Brake system according to EC Directive 71/320 or E CE R13
Two-line brake
Spring-loaded parking brake on both axles
EBS - electronic brake system
Wabco 2S2M = one axle sensed
RSS - stability program
Steel air tank

1 tipper cylinder for 3-way tipping, approx. 70 t initial lifting force,
1 arrester cable
1 pipe system with screw coupling DN20

24 V lighting system according to EC Directive 76/756/E WG
2 seven-chamber tail lights
LED side marker lights
2 clearance lamps
2 contour lights
2 x 7-pin / 1 x 15-pin socket

Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)

Plastic and hot-dip galvanised parts unpainted,
powder-coated attachments/installation parts black

Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48
 

Wheel chock(s) as per regulations
Noise dampers
Single wheel plastic mudguards with spray protection as per regulations
Aluminium trapezoidal underride protection, foldable, unpainted

Gross train weight (perm.): 40 t
Gross weight (techn.): 36 t
Axle assembly load (techn.): 20 t
Fifth-wheel load (techn.): 18 t
Payload: approx. 25 t (but techn. configured for loads up to approx. 35 t)
Tare weight: approx. 6.4 t

Full-steel welded construction with fine-grained special steel floor panels, 5 mm
(slight floor unevenness possible due to weld distortion)
 

Fixed steel plate front wall, 3 mm, approx. 1,360 mm high with excavator protection, lashing eyes, ladder and retaining brackets
2-part aluminium hollow profile side walls, 60/40 mm, approx. 1,200 mm high,
hinged with manual central locking (operated separately for each wall),
foldable when empty = upper self-aligning bearings with screw retention
Steel plate rear wall, 4 mm, approx. 1,300 mm high,
hinged with raised bearing and autom. pneumatic locking
1 handle

Rear markings as per ECE standards
 

2 fixed centre posts in side wall height
2 fixed rear corner posts, raised, with welded discharge chute
(ground clearance when tipped: approx. 550 mm)